达州附近有没有服务

 Jinan Ningrui Machinery Equipment Co., Ltd
 Small sawing machine
  • 60s manual response
  • Give technical reply within 30 min
  • 24 hour free solution

Small sawing machine

The material cut by the small saw is selected by the variable speed handle on the gearbox, and the appropriate feed rate is selected by the handle of the speed regulating valve according to the different raw materials and workpiece shapes. The servo position control module of sawing machine system adopts position control, sampling interpolation and expected control are separated. Due to the electromagnetic mechanical lag and motion inertia, the feed slider can not be moved 0.1 mm by "on" and "off" control. CNC saw is driven by driving wheel and driven wheel

Application fields:

7 * 24-hour free hotline 0531-84233787

adopt Small sawing machine The material of the cutting material is selected by the variable speed handle on the gearbox, and the appropriate feed rate is selected through the handle of the speed regulating valve according to different raw materials and workpiece shapes. The servo position control module of sawing machine system adopts position control, sampling interpolation and expected control are separated. Due to the electromagnetic mechanical lag and motion inertia, the feed slider can not be moved 0.1 mm by "on" and "off" control. CNC saw is driven by driving wheel and driven wheel, and cutting direction of saw blade is controlled by guide rail control frame. After adjusting the rotating bearing, straighten and straighten the band saw blade, and then sweep the saw blade away by the sweeper. The guide rail control frame is supported by the piston rod of hydraulic cylinder, which can fall into the sawn timber. The band saw machine is equipped with manual or hydraulic cylinder clamping and locking mechanism, as well as hydraulic operation valve switch. According to the length (length) of the blank, adjust the position of the ejector rod of the fixed length equipment and lock it. The ejector rod should usually be pressed on the upper edge of the workpiece base. Place the prepared band saw blade on the two saw wheels, clip it into the guide wheel and guide block, and then tighten the saw band with the square head on the tension screw and the force measuring wrench. Tension is usually determined. It's 60-80 nm.


The guide arm of the sawing machine is broken, and the distance between the guide arms is too large. The servo position control module of sawing machine system adopts position control, sampling interpolation and expected control are separated. Due to the electromagnetic mechanical lag and motion inertia, the feed slider can not be moved 0.1 mm by "on" and "off" control. The rolling circumference of saw wheel is too small, so it is recommended to use narrow band saw. Tension of band saw blade (Note: mutual traction force when pulling objects). Cut paper too big. Welding suspected. Abnormal wear of tooth tip. The tip is not inserted. The distance between the guide arms is too large or the guide arms are not at the same level, so it should be adjusted. The guide wheel or tungsten steel of the sawing machine is damaged and should be replaced. Band saw tension too low. Sawn work pieces will break. Welding problems. The tip does not operate properly. The coolant concentration of antifreeze is insufficient or the dosage is too small. View or exchange balls. Adjust the cutting feed or band saw speed. Choose the right tooth profile.


 Small sawing machine

Humanized design, more convenient production and use

 Small sawing machine

Advantages of small sawing machine

Technical parameters of small sawing machine

Main technical parameters Company
*Large bore diameter mm forty
*High feed resistance N sixteen thousand
Spindle * high output torque Nm three hundred and fifty
Taper of spindle hole Morse four
Main motor power Kw three
Spindle speed range r/min 31.5-1400 (grade 12)
X / Y / X fast moving speed mm/min 8000/8000/7000
Up and down travel of headstock mm 600 (mobile)
Left and right travel (x axis) mm eight hundred and fifty
Fore and aft travel (Y axis) mm six hundred
Up and down travel of spindle mm 250 (automatic 240)
Distance between main end face and worktable mm 0-800
Table size mm 1000×650
Table area mm 850×550
Positioning accuracy (x, y) mm 0.05(0.04)
Repeat positioning accuracy (x, y) mm 0.02(0.015)
Machine weight kg three thousand
Overall dimension (length × width × height) mm 2450×2160×2550


More models can also contact us to support customization

Customized service process

01 /06

01

Consulting customer service
All you need is one phone call. Leave the rest to us

02

Understanding needs
Talk to our sales team in detail

03

Planning and design
Professional engineers according to your needs to give a reasonable plan

04

Manufacturing
We will complete the quality and quantity in a reasonable time

05

Technical installation
Professional installation team on site installation, commissioning to stable production

06

Post maintenance
If you have any problems later, you can contact the after-sales engineer

200000+ Customers' choice

With good reputation, excellent quality and sound after-sales service, Jinan Ningrui has won praise in the world, and has made brilliant achievements in many enterprises at home and abroad!

Related cases

24-Hour Hour Hotline
0531-84233787
Online consultation

7 * 24 hours online service

Headquarters address:

Jibei street xibali dongshou-1, Jiyang County, Jinan City, Shandong Province

Online Message

If you are looking for related products or have any other questions, please call our sales hotline at any time 0531-84233787 , you can also leave us a message below, we will serve you warmly!

Online consultation

Ask for a quotation

Sales Hotline

Sales Hotline: 0531-84233787