达州附近有没有服务

 Jinan Ningrui Machinery Equipment Co., Ltd
 Automatic horizontal band sawing machine
  • 60s manual response
  • Give technical reply within 30 min
  • 24 hour free solution

Automatic horizontal band sawing machine

The hydraulic transmission system of automatic horizontal band saw machine is a hydraulic circuit composed of pump, valve, cylinder, oil tank, pipeline and other auxiliary components. It completes the lifting of saw beam and clamping of workpiece under electric control. The stepless speed regulation of feed speed can be realized by speed regulating valve to meet the sawing requirements of different raw materials. The electrical control system consists of a control circuit, which consists of an electrical box, a control box, a junction box, a travel switch and an electromagnet

Application fields:

7 * 24-hour free hotline 0531-84233787

Automatic horizontal band sawing machine Hydraulic transmission system is a hydraulic circuit composed of pump, valve, cylinder, oil tank, pipeline and other auxiliary components. It completes the lifting of saw beam and clamping of workpiece under electric control. The stepless speed regulation of feed speed can be realized by speed regulating valve to meet the sawing requirements of different raw materials. The electrical control system is composed of a control circuit, which is composed of an electrical box, a control box, a junction box, a travel switch, an electromagnet, etc., which is used to control the reversal of the saw blade, the lifting beam of the saw and the clamping of the workpiece, so as to make it follow the required operation procedures. End the normal cutting cycle.


Before starting the lubrication system, be sure to lubricate the machine according to the lubrication parts of the machine tool (wire brush shaft, worm gear box, automatic bearing seat, worm bearing, upper and lower shafts of lifting cylinder and movable vise). Sliding surface clamping screw). Lubricate the worm gear and worm in the worm gear box with No. 30 oil bath, and inject it from the oil filling hole on the upper part of the worm gear box. There is an oil mark on the oil level of the box. between. The oil should be changed after one month's trial. In the future, the oil should be changed every 3-6 months. An oil drain plug is arranged at the lower part of the worm gear box. The saw blade drives the motor installed on the worm gear box, drives the worm gear and worm gear in the worm gear box through the belt pulley and V-belt to drive the automatic wheel to rotate, and then drives the automatic winding saw blade to force the rim to perform the cutting reverse movement. The feed motion of the saw blade is a hydraulic system, including a lifting cylinder and a speed control valve, which controls the descending speed of the saw blade, and then controls the feed of the saw blade (stepless speed regulation). The saw brush rotates at the place where the blade produces chips and follows the blade in the direction of the saw. The cooling pump is used to clean the coolant to remove chips from the serrations. The coolant is in the coolant tank on the right side of the base, and the coolant is directly driven by the water pump.


Press the emergency stop (stop) button, rotate clockwise, the oil pump motor works, the gear pump works, the oil enters the pipeline through the filter, and releases the safety valve to make the system working pressure meet the requirements. Otherwise, press the button inward and all motors will stop working. Press the clamp button on the workpiece to clamp the solenoid valve. While clamping the left side of the clamping oil tank, the left side of the clamping oil cylinder returns to the hydraulic cylinder. When lowering the saw beam, press the operation once and press the pliers, and the hydraulic oil will enter the lifting cylinder with rod chamber through the solenoid valve; the working oil without rod chamber will return to the oil tank through the solenoid valve and one-way speed regulating valve. Quickly look down at the beam and press the down button. The hydraulic pressure works through a solenoid valve. The oil enters the lift cylinder through the rod chamber, and the oil without rod chamber returns to the oil tank through the solenoid valve. When the saw beam is raised, press the up button, and the hydraulic oil enters the rodless chamber of the lifting cylinder through the solenoid valve. The oil with the rod chamber returns to the tank through the solenoid valve. Press the left clamping button to release the hydraulic oil through the left jaw to release the hydraulic oil.


The analog input and output modules of the system make the monitoring of sawing process have a wide range of significance. For example, the saw only needs to increase the feedback of the saw blade deformation to adjust the saw speed adaptively. Adding servo valve can optimize the speed and direction control of sawing process. The processing function of the system makes the processing of data and workpiece more convenient. The Chinese interface and real-time graphical state display of the system make the operation more friendly and intuitive. Because the system uses standard PC, the processing speed of sawing network is faster.


 Automatic horizontal band sawing machine

Humanized design, more convenient production and use

 Automatic horizontal band sawing machine

Advantages of automatic horizontal band sawing machine

Technical parameters of automatic horizontal band sawing machine

Main technical parameters Company
*Large bore diameter mm forty
*High feed resistance N sixteen thousand
Spindle * high output torque Nm three hundred and fifty
Taper of spindle hole Morse four
Main motor power Kw three
Spindle speed range r/min 31.5-1400 (grade 12)
X / Y / X fast moving speed mm/min 8000/8000/7000
Up and down travel of headstock mm 600 (mobile)
Left and right travel (x axis) mm eight hundred and fifty
Fore and aft travel (Y axis) mm six hundred
Up and down travel of spindle mm 250 (automatic 240)
Distance between main end face and worktable mm 0-800
Table size mm 1000×650
Table area mm 850×550
Positioning accuracy (x, y) mm 0.05(0.04)
Repeat positioning accuracy (x, y) mm 0.02(0.015)
Machine weight kg three thousand
Overall dimension (length × width × height) mm 2450×2160×2550


More models can also contact us to support customization

Customized service process

01 /06

01

Consulting customer service
All you need is one phone call. Leave the rest to us

02

Understanding needs
Talk to our sales team in detail

03

Planning and design
Professional engineers according to your needs to give a reasonable plan

04

Manufacturing
We will complete the quality and quantity in a reasonable time

05

Technical installation
Professional installation team on site installation, commissioning to stable production

06

Post maintenance
If you have any problems later, you can contact the after-sales engineer

200000+ Customers' choice

With good reputation, excellent quality and sound after-sales service, Jinan Ningrui has won praise in the world, and has made brilliant achievements in many enterprises at home and abroad!

Related cases

24-Hour Hour Hotline
0531-84233787
Online consultation

7 * 24 hours online service

Headquarters address:

Jibei street xibali dongshou-1, Jiyang County, Jinan City, Shandong Province

Online Message

If you are looking for related products or have any other questions, please call our sales hotline at any time 0531-84233787 , you can also leave us a message below, we will serve you warmly!

Online consultation

Ask for a quotation

Sales Hotline

Sales Hotline: 0531-84233787